Uji Kuat (Kuat Tekan) Paving Block Hasil Konversi Sampah Plastik
Abstract
This research aims to determine the compressive strength of paving blocks produced from plastic waste through a comparison with paving blocks made from a mixture of plastic and sand, as well as factory-produced paving blocks used for the UIN Fatmawati Sukarno Bengkulu campus courtyard. The research is conducted using an experimental method, starting with the manufacturing of plastic-based paving blocks and followed by strength testing in the civil engineering laboratory of the University of Bengkulu. The results of the research show that the compressive strength of factory-produced paving blocks made from sand and cement averages 5.9 MPa, while the compressive strength of paving blocks made from a mixture of plastic and sand averages 1.32 MPa, and the average compressive strength of paving blocks is 2.23 MPa. In conclusion, the compressive strength of paving blocks made from pure plastic or a mixture of plastic and sand is still below the SNI 03-0691-1996 standard due to the brittle nature of plastic.
Keywords: Conversion, Plastic, Paving Block
References
Brizi, M. R. A., Rakhmawati, A., & Arnandha, Y. (2021). Pemanfaatan Limbah Plastik LDPE sebagai Bahan Campuran Pembuatan Bata Beton (Paving Block). Jurnal Rekayasa Infrastruktur Sipil, 1(2), 2–7. http://dx.doi.org/10.31002/.v1i2.3521
Erdin, E. K. Z., Zainuri, Z., & Soehardi, F. (2021). Kualitas Paving Block dengan Menggunakan Limbah Plastik Polypropylene Terhadap Kuat Tekan. Jurnal Teknik, 15(2), 185–190. https://doi.org/10.31849/teknik.v15i2.7435
Karuniastuti, N. (2013). Bahaya Plastik Terhadap Kesehatan dan Lingkungan. Swara Patra: Majalah Pusdiklat Migas, 3(1), 6–14. http://ejurnal.ppsdmmigas.esdm.go.id/sp/index.php/swarapatra/article/view/43
Khoirunnisa, F., & Kadarohman, A. (2022). Dilema Penggunaan Plastik: Kebutuhan dan Keberlanjutan Lingkungan (Tinjauan Aspek Etika dalam Perspektif Aksiologi). Jurnal Filsafat Indonesia, 5(1), 1–8. https://doi.org/10.23887/jfi.v5i1.41855
Nasution, R. S. (2015). Berbagai Cara Penanggulangan Limbah Plastik. Elkawnie: Journal of Islamic Science and Technology, 1(1), 97–104. http://dx.doi.org/10.22373/ekw.v1i1.522
Sari, K. I., & Nusa, A. B. (2019). Pemanfaatan Limbah Plastik HDPE (High Density Polythylene) sebagai Bahan Pembuatan Paving Block. Jurnal Teknik Sipil, 15(1), 29–33. https://jurnal.uisu.ac.id/index.php/but/article/view/1869
Sudarno, S. (2021). Pemanfaatan Limbah Plastik untuk Pembuatan Paving block. Jurnal Teknik Sipil Terapan, 3(2), 101-110. http://dx.doi.org/10.47600/jtst.v3i2.290
Surono, U. B. (2013). Berbagai Metode Konversi Sampah Plastik Menjadi Bahan Bakar Minyak. Jurnal Teknik, 9(1), 32–40. https://e-journal.janabadra.ac.id/index.php/jurnalteknik/article/viewFile/2676/1785
Wahyudi, J., Prayitno, H. T., & Astuti, A. D. (2018). Pemanfaatan Limbah Plastik sebagai Bahan Baku Pembuatan Bahan Bakar Alternatif. Jurnal Litbang: Media Informasi Penelitian, Pengembangan dan IPTEK, 14(1), 58–67. https://ejurnal-litbang.patikab.go.id/index.php/jl/article/view/109
Winursito, I. (2013). Perkembangan Penelitian dan Pemakaian Plastik Biodegradabel di Indonesia. Jurnal Riset Industri,7(3), 251-262. https://media.neliti.com/media/publications/178576-ID-perkembangan-penelitian-dan-pemakaian-pl.pdf
Wirasasmita, R. H., Arianti, B. D. D., Uska, M. Z., Kholisho, Y. N., Wardi, Z., Gunadi, R. A. A., Parlindungan, D. P., Parta Santi, A. U., Aswir, & Aburahman, A. (2020). Bahaya Sampah Plastik bagi Kesehatan dan Lingkungan. ABSYARA: Jurnal Pengabdian Pada Masyarakat, 1(2714–6286), 1–8. https://doi.org/10.29408/ab.v1i2.2749
